Squier electric guitar Ads | Gumtree Classifieds South Africa

Clear All

Results for squier electric guitar in All Categories in South Africa

SSS / HSS / HSH Prewired Electronics for Strat style guitars – Solderless

R 649

Save

A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 single coil pickups, 1 humbucker and 2 single coils or 2 humbuckers and one single coil. Since the components are customizable you can chose your desired layout and values. The layout is a per Fender USA/MEX Standard strat. This will fit squier or other guitars but we can not guarantee the layout will be the same, the pots and switch need to be fixed to the plate, if you are unsure if this plate will fit onto your pickguard you can purchase one of our pickguards, all the pickguards we sell at Valley Sound for Strat will work.Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometers (Either flat bottom or with the notch – depending what we have available). Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our solderless connector. It is easy to do, the connector is spring activated so you just press on the orange part with a screwdriver, insert the wire and release. All the ground wires go to the bottom terminals and each hot goes to top terminals. They will be colour coded so you know where to put the hot of each component:Output jack hot gets connected to the white terminalNeck pickup to the blue terminalMiddle pickup to the red terminalBridge pickup to the yellow terminalPlease note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. Please order via our Valley Sound website in order to select from these customisable options.Volume Potentiometer options:– Linear (B250k / 500k)– Audio Taper (A250k / 500k)Most modern guitar manufacturers (or non Fender USA Standard guitars) use 250k Linear pots for volume, Standard / Vintage US Strats typically come with Audio Taper volume pots. Both work but linear has more even control, Audio Taper has most of the control happen between 7 – 10.Volume Treble Bleed options:– Simple– Kinman– DuncanTone Potentiometers options:– Linear (B250k / 500k)– Audio Taper (A250k / 500k)Most guitars use Audio Taper pots for tone, Some people prefer a Linear pot for tone as it allows for more fine tuning of a “sweet spot”. 250k Tone pots are generally used for all single coil pickups and 500k tone pots for humbucker pickups but this is also personal preference and choice. 250k is less bright than 500k.Tone Capacitor Value options:– 0.022uF (or 22nf)– 0.047uF (or 47nf)1st Tone pot assigned control options:– Neck pickup– Both Neck and Middle pickups2nd Tone pot assigned control options:– Middle– Both Middle and Bridge pickups– Bridge Pickup

2mo

VERIFIED

Parkwood

Prewired Electronic Assembly for S/S/S Style Strat Guitars with treble bleed mod – Solder-in

R 599

Save

A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 Single Coil Pickups (SSS)Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometer for Volume and tones. Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our electronics. We also have the bridge grounding and output jack wire pre-soldered onto the assembly so you can feed the white and black wire through to your output jack (jacks sold separately) and 2nd black wire to your bridge for grounding. All the ground wires from your pickups go to the top of the volume pot, 3 blobs of solder are on top of the pot for quick soldering. The hots go to each position on the switch.Please note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. We can do solderless wiring harnesses and we can make any custom wiring assembly, browse the Valley Sound website for examples of other wiring configurations and mods we have done.SPECS:This standard solder-in wiring harness assembly comes with the following specs and components:– A250k Full Size Volume Potentiometer with brass shaft– Trebble bleed mod to prevent trebble loss when rolling back the volume– A250k Full Size Tone Potentiometers with brass shaft– Tone Pot 1 controlls both Neck and Middle pickups tone– Tone Pot 2 controlls Bridge pickup tone– Tone Capacitor Value: 0.047uF (or 47nf)– Vintage Style 5 way selector switch– Selector Switch tip: Black, Cream or White (White is Standard if you do not inform us of a different colour choice)Potentiometer knobs are not included, please purchase them separately should you require. Potentiometers used will either be concave top or flat top, which ever we have available.PLEASE NOTE: Thin bodied guitars with shallow routing (such as Squier Bullet and Affinity) may not accommodate this larger than standard switch, you need at least 35mm routing depth, check the area where your switch goes, if the routing for your switch is 35mm or deeper you can fit this pickguard without additional routing to the body. This grounding plate is made to the exact layout of Fender and Squier Stratocaster electronic layouts, we can not guarantee that it will fit other copies. Guitar parts available from our online store: www.valleysound.co.za A great selection of direct replacement parts for Gibson or Fender type electric guitars as well as guitar accessories. Please order online: www.valleysound.co.za

2mo

VERIFIED

Mosselbaai

S/S/S Prewired Electronic Assembly for Stratocaster Guitars USA Layout – Solder-in

R 649

Save

A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 Single Coil Pickups (SSS)Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometer for Volume and tones with USA spec 9.5mm shaft thickness. Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our electronics. We also have the bridge grounding and output jack wire pre-soldered onto the assembly so you can feed the white and black wire through to your output jack (jacks sold separately) and 2nd black wire to your bridge for grounding. All the ground wires from your pickups go to the top of the volume pot, the hots go to each position on the switch.Please note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. We can do solderless wiring harnesses and we can make any custom wiring assembly, browse the Valley Sound website for examples of other wiring configurations and mods we have done.SPECS:This standard solder-in wiring harness assembly comes with the following specs and components:– A250k Full Size Volume and Tone Potentiometers with brass shaft and USA CTS Spec (you need to enlarge your pot holes if you have an asian import pickguard – if you have a Valley Sound pickguard or USA Fender it will fit perfect.– Tone Pot 1 controls Neck Pickup– Tone Pot 2 controls Middle Pickup– Tone Capacitor Value: 0.022uF (or 22nf)– Vintage Style 5 way selector switch– Selector Switch tip: Black, Cream or White (White is Standard if you do not inform us of a different colour choice)Potentiometer knobs are not included, please purchase them separately should you require.PLEASE NOTE: Thin bodied guitars with shallow routing (such as Squier Bullet and Affinity) may not accommodate this larger than standard switch, you need at least 30mm routing depth, check the area where your switch goes, if the routing for your switch is 30mm or deeper you can fit this pickguard without additional routing to the body. This grounding plate is made to the exact layout of Fender and Squier Stratocaster electronic layouts, we can not guarantee that it will fit other copies.Guitar parts available from our online store: www.valleysound.co.za A great selection of direct replacement parts for Gibson or Fender type electric guitars as well as guitar accessories. Please order online: www.valleysound.co.za

2mo

VERIFIED

Springbok

...

"squier electric guitar" in South Africa

squier electric guitar in South Africa (110 results)

Results for squier electric guitar in All Categories in South Africa